Top 9 Arduino Switch Module – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. AiTrip


10 Pack TTP223B Digital Touch Capacitive Sensor Switch Module DIY for Arduino Raspberry Pi

AiTrip #ad - This module is capacitive type jog mode touch switch module that is based on a touch detection IC TTP223B. Feature:ttp223b chip, low power consumption, sig; both positive and negative can be used as a touch surface, and power supply is DC 2-5.

5v; green led indicator, and it is bright when power on right; Control port: GND, VCC, and replace the traditional touch of a button. You can put to a thin paper non-metallic cover the surface of the module, that you can put it hidden in the walls, when touch the correct location of the module, desktops and other buttons.

In the normal state, low power consumption, but when a finger touches the corresponding position, the module output high, the module output low, if not touched for 12 seconds, switch to low-power mode. Module can be installed in such as surface plastic, glass of non-metallic materials. Allows you to remove the worry of conventional push-type keys.
BrandAiTrip #ad
ManufacturerAiTrip #ad



And Photoelectric Switch for Arduino Smart Car Robot Raspberry PI 4 3 Model B, OSOYOO 10PCS Obstacle Avoidance Sensor Module with IR Transmitting, Receiving Tube

OSOYOO #ad - It has red power indicator. Can be used for 3-5v dc power supply modules. Ir infrared obstacle avoidance sensor Module can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and black and white line tracking and so on.

The module detects the distance 2 ~ 30cm, detection angle 35 °, the distance can detect potential is adjusted. The output port out sensor module can be directly connected to the microcontroller IO port, you can directly drive a 5V relay. It has a pair of infrared transmitting and receiving tube, reflected infrared receiving tube, after the comparator circuit processing, when detecting direction meet with obstacles reflecting surface, tube infrared emit a certain frequency, green indicator will light up, at the same time signal output interface to output digital signal a low level signal.
BrandOSOYOO #ad
ManufacturerShenzhen Vership Co. LTD #ad
Height1 Inches
Length5.3 Inches
Width3.2 Inches
Part NumberZZ20160410

3. Youliang


Youliang 2PCS KY-004 3 Pin Button Key Tactile Switch Sensor Breakout Board Module For Arduino Raspberry Pie

Youliang #ad - Model: ky-004. Rating: 50ma 12VDC. Good for use just anywhere on your project and great for debugging a project. Key switch module and a digital interface, built-in 13 light build a simple circuit to produce key warning lamp. Package Included:2PCS. This module is ideally suited to adding a button to your projects and will output a high signal when pressed. Contact resistance : 50mOhm maxinitial.
BrandYouliang #ad

4. HJ Garden


STM32 etc. 830 Breadboard + Jumper + Power Module + Resistor + Capacitor + LED + Switch Pack of 458pcs, Raspberry Pi, HJ Garden Electronic Component Assorted Kit for Arduino

HJ Garden #ad - Breadboard: 830 tie-point mb-102 solderless breadboard, size 16. 5x5. 5x085cm. Power adaptor: 12v 1a 12W, can supplying power for project stability. Power module: mb-102 breadboard dc voltage-stabilized source module, output 700 ma max, 3. 3v; input voltage: DC 6. 5-12v or usb power supply, compatible with 5V, two way independent control, can switch 0V / 3.3v / 5v. Jumper: 65pcs colorful breadboard jumper, convenient to connect module. This kit contains power supply components for Arduino, Raspberry Pi that project based on breadboard.
BrandHJ Garden #ad
ManufacturerHJ Garden #ad
Part NumberMB102K-458P

5. Gump's grocery


Gump's grocery 10PCS TTP223 Capacitive Touch Switch Button Self-Lock Module for Arduino

Gump's grocery #ad - Size:1. 4cm*1. 05cm*01cm. Material: CCL. Trigger setting mode:1- Greater than Short;0- Greater than No Short. Color:RED. Power:2. 5-5. 5v.
BrandGump's grocery #ad
ManufacturerGump's grocery #ad
Part NumberTG211

6. Gump's grocery


Gump's grocery Microphone Sensor High Sensitivity Sound Detecte Voice Switch Module for Arduino

Gump's grocery #ad - 2. Output form: digital switching outputs 0 and 1 high and low Level. Adjustable sensitivity adjusted by the blue digital potentiometers. Easy installation with bolt hole. Operating voltage 3. 3v-5v. It’s to be used for detecting the sound intensity of ambient. Small pcb size :l*w 3. 2* 1. 7cm/1. 26"*067".
BrandGump's grocery #ad
ManufacturerGump's grocery #ad
Part NumberTG242



DAOKI 10PCS KY-003 Hall Effect Magnetic Sensor Module 3144 for Arduino PIC AVR Smart Car

DAOKI #ad - Current:1A. Base material: FR4. Board thickness: 1. 6mm. 1. 5 x 1. 3 x 04cm. Size: approx. Option: micro usb, usb 2. 0, mini usb, b type usb, usb 3.0, usb 2. 0 male.
BrandDAOKI #ad
ManufacturerDAOKI #ad
Part NumberTS-US-313

8. SunFounder


SunFounder 4 Channel 5V Relay Shield Module Compatible with Arduino R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi

SunFounder #ad - Applications: supports all mcu control, The industrial field, Smart home control, PLC control, VCC system Power and so on.5v 4-channel relay interface board, and each one needs 15-20mA Driver Current. Standard interface that can be controlled directly by microcontroller Compatible with Arduino, AVR, ARM, MSP430, PIC, DSP, 8051, ARM, TTL logic. Equiped with high-current relay, AC250V 10A ; DC30V 10A. Indication led’s for Relay output status.
BrandSunFounder #ad
ManufacturerSunFounder #ad
Height0.8 Inches
Length3.2 Inches
Weight0.02 Pounds
Width2.9 Inches
Part Number4C-5V



AITRIP 8 Pack 3V 1 Channel Relay Power Switch Module with Optocoupler Opto Isolation High Level Trigger for IOT ESP8266 Development Board

AITRIP #ad - 3v/3. 3v power relay module- this relay board provides a single relay that can be controlled by any 3V/3. 3v digital input from your microcontroller IO.

Long life - fast response time less than 20ms and long lifetime up to 100, 000 times snap action with diode freewheel protection. High level triggerthe relay module is triggered by high level signal, which can be input from microcontroller IO. Wide application- these 3v relay board works well with arm /pic /avR /MCU/Raspberry/CNC machine/ PS4/3. 3v /nodemcu/ esp8266 module etc. Can be selected by jumper relay and TTL or ground. 30vdc 250vac load equiped with high-current relay, ac250v 10a ; dc30v 10A, each relay has normally open and normally closed contact.
BrandAITRIP #ad
ManufacturerAITRIP #ad
Part NumberEC14323